diff --git a/board/common/image/image-readme/README.md b/board/common/image/image-readme/README.md
index b11a3b77e..e92f0792d 100644
--- a/board/common/image/image-readme/README.md
+++ b/board/common/image/image-readme/README.md
@@ -34,7 +34,7 @@ Depending on how your Linux installation is set up, the following may
 require being run with superuser privileges, i.e., you may need to
 repend the command with 'sudo'.
 
-    $ ./qemu.sh
+    $ ./qemu/run.sh
 
 You should now see the Infix init system booting up.  When the final
 "Please press Enter to activate this console." is shown, press Enter
@@ -75,13 +75,13 @@ interface, which requires the following extra package:
 
 We can now enter the configuration:
 
-    $ ./qemu.sh -c
+    $ ./qemu/run.sh -c
 
 Go down to *Networking*, select *TAP*, now you can change the *Number of
 TAPs*, e.g. to 10.  Exit and save the configuration, then you can start
 Qemu again:
 
-   ./qemu.sh
+    $ ./qemu/run.sh
 
 > Make sure to do a factory reset from the CLI, otherwise you will be
 > stuck with that single interface from before.
diff --git a/board/common/qemu/run.sh b/board/common/qemu/run.sh
index 48052c530..ee7d7d85e 100755
--- a/board/common/qemu/run.sh
+++ b/board/common/qemu/run.sh
@@ -10,12 +10,12 @@
 #
 # and then call this script with:
 #
-#    ./qemu.sh -c
+#    ./run.sh -c
 #
 # To bring up a menuconfig dialog.  Select `Exit` and save the changes.
 # For more help, see:_
 #
-#    ./qemu.sh -h
+#    ./run.sh -h
 #
 # shellcheck disable=SC3037
 
@@ -40,7 +40,7 @@ usage()
     echo "         Also, qemu.cfg has QEMU_APPEND which can affect this."
     echo
     echo "Example:"
-    echo "  qemu.sh -- finit.debug"
+    echo "  $prognm -- finit.debug"
     echo "___________________________________________________________________"
     echo "Note: 'kconfig-frontends' package (Debian/Ubuntu) must be installed"
     echo "      for -c to work: sudo apt install kconfig-frontents"
diff --git a/doc/virtual.md b/doc/virtual.md
index 21a9058b6..52c12d5ac 100644
--- a/doc/virtual.md
+++ b/doc/virtual.md
@@ -18,11 +18,11 @@ QEMU
 > relevant Qemu packages are pulled in as well.  This trick, installing
 > [virt-manager][virt], helps set up Qemu networking on your system.
 
-A virtualized Infix x86_64 instance can easily be launched from a Linux
-system, with [Qemu][] installed, by issuing:
+A virtualized Infix x86_64 instance can be launched from a Linux system,
+with [Qemu][] installed, by issuing:
 
 ```
-$ ./qemu.sh
+$ ./qemu/run.sh
 ...
 ```
 
@@ -35,7 +35,7 @@ $ make run
 ```
 
 To change settings, e.g. networking, <kbd>make run-menuconfig</kbd>, or
-from a pre-built Infix release tarball, using <kbd>./qemu.sh -c</kbd>
+from a pre-built Infix release tarball, using <kbd>./qemu/run.sh -c</kbd>
 
 The Infix test suite is built around Qemu and [Qeneth][qeth], see: