Flashed with the 1.3 Firmware fom G1LRO as described here. https://g1lro.uk/?p=676.
Got the TX working but the RX wont work with VCos / Hidraw.
linked dev/hidrawX to /dev/cm108gpio. DTMF decoding works but i dont hear my voice when i activate the parrot.
Also tested it on my SHARI SA818s setup which also uses a cm108 and same bindings, same result. Sadly i'm only getting it to work with VOX and not with HIDRAW.
[GLOBAL]
#MODULE_PATH = /usr/lib/arm-linux-gnueabihf/svxlink
LOGIC_CORE_PATH = /usr/lib/arm-linux-gnueabihf/svxlink
LOGICS = SimplexLogic,ReflectorLogic
CFG_DIR = svxlink.d
#TIMESTAMP_FORMAT = "%c"
TIMESTAMP_FORMAT="%d.%m.%Y %H:%M:%S"
CARD_SAMPLE_RATE = 48000
CARD_CHANNELS = 1
#LOCATION_INFO = LocationInfo
LINKS = LinkToReflector
[SimplexLogic]
TYPE = Simplex
RX = Rx1
TX = Tx1
#mit Echolink
#MODULES = ModuleHelp,ModuleParrot,ModuleEchoLink
ohne Echolink
MODULES = ModuleHelp,ModuleParrot
CALLSIGN = OE1SXM
#SHORT_IDENT_INTERVAL = 15
LONG_IDENT_INTERVAL = 30
EVENT_HANDLER = /usr/share/svxlink/events.tcl
DEFAULT_LANG = de_DE
#RGR_SOUND_DELAY = 100
#RGR_SOUND_ALWAYS = 1
MACROS = Macros
FX_GAIN_NORMAL = 0
FX_GAIN_LOW = -25
DTMF_CTRL_PTY = /tmp/dtmf_svx
MUTE_RX_ON_TX=1
MUTE_TX_ON_RX=1
[ReflectorLogic]
TYPE=ReflectorV2
HOSTS=NONE
HOST_PORT=5300
CALLSIGN=MYCALL
AUTH_KEY="GET YOURSELF A KEY"
DEFAULT_TG = 232110
MONITOR_TGS = 232,2321,23211,2323,232777,20,2329
TG_SELECT_TIMEOUT = 30
ANNOUNCE_REMOTE_MIN_INTERVAL = 300
EVENT_HANDLER = /usr/share/svxlink/events.tcl
NODE_INFO_FILE = /etc/svxlink/node_info.json
QSY_PENDING_TIMEOUT = 15
TMP_MONITOR_TIMEOUT = 3600
UDP_HEARTBEAT_INTERVAL = 15
DEFAULT_LANG = de_DE
VERBOSE = 0
[LinkToReflector]
CONNECT_LOGICS=SimplexLogic:9:,ReflectorLogic
DEFAULT_ACTIVE=1
OPTIONS = DEFAULT_CONNECT,NO_DISCONNECT
TIMEOUT=300
[Macros]
1=EchoLink:9999#
9=Parrot:0123456789#
03400=EchoLink:9999#
[Rx1]
TYPE = Local
AUDIO_DEV = alsa:plughw:1
AUDIO_CHANNEL = 0
#SQL_DET = HIDRAW not working on AIOC with CM108 ID's
SQL_DET = VOX
VOX_FILTER_DEPTH=20
VOX_THRESH=270
VOX_HANGTIME=1000
SIGLEV_SLOPE=1
SIGLEV_OFFSET=0
SIGLEV_OPEN_THRESH=30
SIGLEV_CLOSE_THRESH=10
HID_DEVICE = /dev/cm108gpio
HID_SQL_PIN = VOL_DN
#SQL_START_DELAY = 20
SQL_START_DELAY = 1500
SQL_DELAY = 20
SQL_HANGTIME = 0
SQL_TIMEOUT = 180
DEEMPHASIS = 1
#SQL_TAIL_ELIM = 250
PREAMP = 0
#PEAK_METER = 1
DTMF_DEC_TYPE = INTERNAL
DTMF_MUTING = 1
DTMF_HANGTIME = 40
DTMF_SERIAL = /dev/ttyS0
#1750_MUTING = 1
[Tx1]
TYPE = Local
TX_ID = T
AUDIO_DEV = alsa:plughw:1
AUDIO_CHANNEL = 0
LIMITER_THRESH = -6
PTT_TYPE = Hidraw
PTT_PORT = /dev/ttyS0
PTT_PIN = DTR!RTS
HID_DEVICE = /dev/cm108gpio
HID_PTT_PIN = GPIO3
TX_DELAY = 600
PREEMPHASIS = 1
DTMF_TONE_LENGTH = 100
DTMF_TONE_SPACING = 50
DTMF_DIGIT_PWR = -15
#MASTER_GAIN = 3.0
TX_AUDIO_LEVEL=1.0
Flashed with the 1.3 Firmware fom G1LRO as described here. https://g1lro.uk/?p=676.
Got the TX working but the RX wont work with VCos / Hidraw.
linked dev/hidrawX to /dev/cm108gpio. DTMF decoding works but i dont hear my voice when i activate the parrot.
Also tested it on my SHARI SA818s setup which also uses a cm108 and same bindings, same result. Sadly i'm only getting it to work with VOX and not with HIDRAW.
[GLOBAL]
#MODULE_PATH = /usr/lib/arm-linux-gnueabihf/svxlink
LOGIC_CORE_PATH = /usr/lib/arm-linux-gnueabihf/svxlink
LOGICS = SimplexLogic,ReflectorLogic
CFG_DIR = svxlink.d
#TIMESTAMP_FORMAT = "%c"
TIMESTAMP_FORMAT="%d.%m.%Y %H:%M:%S"
CARD_SAMPLE_RATE = 48000
CARD_CHANNELS = 1
#LOCATION_INFO = LocationInfo
LINKS = LinkToReflector
[SimplexLogic]
TYPE = Simplex
RX = Rx1
TX = Tx1
#mit Echolink
#MODULES = ModuleHelp,ModuleParrot,ModuleEchoLink
ohne Echolink
MODULES = ModuleHelp,ModuleParrot
CALLSIGN = OE1SXM
#SHORT_IDENT_INTERVAL = 15
LONG_IDENT_INTERVAL = 30
EVENT_HANDLER = /usr/share/svxlink/events.tcl
DEFAULT_LANG = de_DE
#RGR_SOUND_DELAY = 100
#RGR_SOUND_ALWAYS = 1
MACROS = Macros
FX_GAIN_NORMAL = 0
FX_GAIN_LOW = -25
DTMF_CTRL_PTY = /tmp/dtmf_svx
MUTE_RX_ON_TX=1
MUTE_TX_ON_RX=1
[ReflectorLogic]
TYPE=ReflectorV2
HOSTS=NONE
HOST_PORT=5300
CALLSIGN=MYCALL
AUTH_KEY="GET YOURSELF A KEY"
DEFAULT_TG = 232110
MONITOR_TGS = 232,2321,23211,2323,232777,20,2329
TG_SELECT_TIMEOUT = 30
ANNOUNCE_REMOTE_MIN_INTERVAL = 300
EVENT_HANDLER = /usr/share/svxlink/events.tcl
NODE_INFO_FILE = /etc/svxlink/node_info.json
QSY_PENDING_TIMEOUT = 15
TMP_MONITOR_TIMEOUT = 3600
UDP_HEARTBEAT_INTERVAL = 15
DEFAULT_LANG = de_DE
VERBOSE = 0
[LinkToReflector]
CONNECT_LOGICS=SimplexLogic:9:,ReflectorLogic
DEFAULT_ACTIVE=1
OPTIONS = DEFAULT_CONNECT,NO_DISCONNECT
TIMEOUT=300
[Macros]
1=EchoLink:9999#
9=Parrot:0123456789#
03400=EchoLink:9999#
[Rx1]
TYPE = Local
AUDIO_DEV = alsa:plughw:1
AUDIO_CHANNEL = 0
#SQL_DET = HIDRAW not working on AIOC with CM108 ID's
SQL_DET = VOX
VOX_FILTER_DEPTH=20
VOX_THRESH=270
VOX_HANGTIME=1000
SIGLEV_SLOPE=1
SIGLEV_OFFSET=0
SIGLEV_OPEN_THRESH=30
SIGLEV_CLOSE_THRESH=10
HID_DEVICE = /dev/cm108gpio
HID_SQL_PIN = VOL_DN
#SQL_START_DELAY = 20
SQL_START_DELAY = 1500
SQL_DELAY = 20
SQL_HANGTIME = 0
SQL_TIMEOUT = 180
DEEMPHASIS = 1
#SQL_TAIL_ELIM = 250
PREAMP = 0
#PEAK_METER = 1
DTMF_DEC_TYPE = INTERNAL
DTMF_MUTING = 1
DTMF_HANGTIME = 40
DTMF_SERIAL = /dev/ttyS0
#1750_MUTING = 1
[Tx1]
TYPE = Local
TX_ID = T
AUDIO_DEV = alsa:plughw:1
AUDIO_CHANNEL = 0
LIMITER_THRESH = -6
PTT_TYPE = Hidraw
PTT_PORT = /dev/ttyS0
PTT_PIN = DTR!RTS
HID_DEVICE = /dev/cm108gpio
HID_PTT_PIN = GPIO3
TX_DELAY = 600
PREEMPHASIS = 1
DTMF_TONE_LENGTH = 100
DTMF_TONE_SPACING = 50
DTMF_DIGIT_PWR = -15
#MASTER_GAIN = 3.0
TX_AUDIO_LEVEL=1.0