Pushing data to Thingspeak

README.md

@@ -1,178 +1,3 @@
-AirPi
-========
+forked from tomhartley/AirPi
 
-A Raspberry Pi weather station and air quality monitor.
-
-This is the code for the project located at http://airpi.es
-
-Currently it is split into airpi.py, as well as multiple input and multiple output plugins. airpi.py collects data from each of the input plugins specified in sensors.cfg, and then passes the data provided by them to each output defined in outputs.cfg. The code for each sensor plugin is contained in the 'sensors' folder and the code for each output plugin in the 'outputs' folder.
-
-Some of the files are based off code for the Raspberry Pi written by Adafruit: https://github.com/adafruit/Adafruit-Raspberry-Pi-Python-Code
-
-For installation instructions, see http://airpi.es/kit.php
-
-## Installation
-
-### Prerequisites
-
-You will need to install the following dependencies:
-
-`sudo apt-get install git-core python-dev python-pip python-smbus libxml2-dev libxslt1-dev python-lxml i2c-tools`
-
-and
-
-`sudo pip install rpi.gpio requests`
-
-AirPi requires python-eeml.  To install:
-
-```
-cd ~/git
-git clone https://github.com/petervizi/python-eeml.git
-cd python-eeml
-sudo python setup.py install
-```
-
-### i2c
-
-To set up i2c, first add your user to the i2c group.  For example, if your username is "pi":
-
-`sudo adduser pi i2c`
-
-Now, add the modules needed.
-
-`sudo nano /etc/modules`
-
-Add the following two lines to the end of the file:
-
-```
-i2c-bcm2708
-i2c-dev
-```
-
-Exit by pressing CTRL+X, followed by y to confirm you want to save, and ⏎ (enter) to confirm the filename.
-
-Finally, unblacklist i2c by running the following command:
-
-`sudo nano /etc/modprobe.d/raspi-blacklist.conf`
-
-Add a `#` character  at the beginning of the line `blacklist i2c-bcm2708`. Then exit in the same way as last time.
-
-Now, reboot your Raspberry Pi:
-
-`sudo reboot`
-
-### Board Version
-
-Let's check to see which board version you have.  Run:
-
-`sudo i2cdetect -y 0`
-
-You should see this as the output:
-
-```
-     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
-00:          -- -- -- -- -- -- -- -- -- -- -- -- -- 
-10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
-20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
-30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
-40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
-50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
-60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
-70: -- -- -- -- -- -- -- 77
-```
-
-If not, run:
-
-`sudo i2cdetect -y 1`
-
-and you should see the above.  This tells you if your board is version 0 or 1.  This is important for the next step.
-
-### Get The AirPi Code
-
-Clone this repo into your git directory (or wherever you want):
-
-```
-cd ~/git
-git clone https://github.com/tomhartley/AirPi.git
-cd AirPi
-```
-
-### Configuring
-
-Edit the settings file by running:
-
-`nano sensors.cfg`
-
-The start of the file should look like this:
-
-```
-[BMP085-temp]
-filename=bmp085
-enabled=on
-measurement=temp
-i2cbus = 1
-
-[BMP085-pres]
-filename=bmp085
-enabled=on
-measurement=pres
-mslp=on
-i2cbus = 1
-altitude=40
-```
-
-If your board version is "0" change both instances of `i2cbus = 1` to `i2cbus = 1`
-
-Press CTRL+X to exit the file, when prompted, press "y" to save the file.
-
-If you want to push the data to Xively, edit the `outputs.cfg` file:
-
-`nano outputs.cfg`
-
-The start of the file should look like this:
-
-```
-[Print]
-filename=print
-enabled=on
-
-[Xively]
-filename=xively
-enabled=on
-APIKey=xxxxxxxxxx
-FeedID=xxxxxxxxxx
-```
-
-If you have registered with https://xively.com - you can add your API Key and Feed ID here.
-
-## Running
-
-AirPi **must** be run as root.
-
-`sudo python Airpie.py`
-
-If everything is working, you should see output similar to this:
-
-```
-Success: Loaded sensor plugin BMP085-temp
-Success: Loaded sensor plugin BMP085-pres
-Success: Loaded sensor plugin MCP3008
-Success: Loaded sensor plugin DHT22
-Success: Loaded sensor plugin LDR
-Success: Loaded sensor plugin MiCS-2710
-Success: Loaded sensor plugin MiCS-5525
-Success: Loaded sensor plugin Mic
-Success: Loaded output plugin Print
-Success: Loaded output plugin Xively
-
-Time: 2014-06-04 09:10:18.942625
-Temperature: 30.2 C
-Pressure: 992.55 hPa
-Relative_Humidity: 35.9000015259 %
-Light_Level: 3149.10025707 Ohms
-Nitrogen_Dioxide: 9085.82089552 Ohms
-Carbon_Monoxide: 389473.684211 Ohms
-Volume: 338.709677419 mV
-Uploaded successfully
-
-```
+added Pushing data to Thingspeak 

outputs.cfg

@@ -7,3 +7,8 @@ filename=xively
 enabled=on
 APIKey=YYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYY
 FeedID=XXXXXXXXXX
+
+[Thingspeak]
+filename=Thingspeak
+enabled=on
+APIKey=YYYYYYYYYYYYYYYYYY

outputs/Thingspeak.py

@@ -0,0 +1,27 @@
+#Pushing data to Thingspeak
+# python
+
+import output
+import datetime
+import httplib, urllib
+
+class ThingSpeak(output.Output):
+    requiredData = ["APIKey"]
+    optionalData = []
+    def __init__(self,data):
+        self.APIKey=data["APIKey"]
+    def outputData(self,dataPoints):
+        Data = ["1","2","3","4","5","6","7"]
+        j = 0
+	for i in dataPoints:
+            Data[j] = str(i["value"])
+            j = j + 1
+        params = urllib.urlencode({'field1': Data[0], 'field2': Data[1],'field3': Data[2],'field4': Data[3], 'field5': Data[4] 'field6': Data[5],'field7': Data[6],'key':self.APIKey})
+        headers = {"Content-type": "application/x-www-form-urlencoded","Accept":"text/plain"}
+        conn = httplib.HTTPConnection("api.thingspeak.com:80")
+        conn.request("POST", "/update", params, headers)
+        response = conn.getresponse()
+        print response.status, response.reason
+        data = response.read()
+        conn.close()
+	return True